Thứ Sáu, 24 tháng 9, 2010

Line array

From Wikipedia, the free encyclopedia
Jump to: navigation, search

A line array is a loudspeaker system that is made up of a number of loudspeaker elements coupled together in a line segment to create a near-line source of sound. The distance between adjacent drivers is close enough that they constructively interfere with each other to send sound waves farther than traditional horn-loaded loudspeakers, and with a more evenly distributed sound output pattern.

Line arrays can be oriented in any direction, but their primary use in public address is in vertical arrays which provide a very narrow vertical output pattern useful for focusing sound at audiences without wasting output energy on ceilings or empty air above the audience. A vertical line array displays a normally-wide horizontal pattern useful for supplying sound to the majority of a concert audience. Horizontal line arrays, by contrast, have a very narrow horizontal output pattern and a tall vertical pattern. A row of subwoofers along the front edge of a concert stage can behave as a horizontal line array unless the signal supplied to them is adjusted (delayed, polarized, equalized) to shape the pattern otherwise. Loudspeakers can be designed to be arrayed horizontally without behaving as a horizontal line source.[1]

Modern line arrays use separate drivers for high-, mid- and low-frequency passbands. For the line source to work, the drivers in each passband need to be in a line. Therefore, each enclosure must be designed to rig together closely to form columns composed of high-, mid- and low-frequency speaker drivers. Increasing the number of drivers in each enclosure increases the frequency range and maximum sound pressure level, whilst adding additional boxes to the array will also lower the frequency in which the array achieves a directional dispersion pattern.

The large format line array has become the standard for large concert venues and outdoor festivals, where such systems can be flown (rigged, suspended) from a structural beam, ground support tower[2] or off a tall A-frame tower.[3]. Since the enclosures rig together and hang from a single point, they are more convenient to assemble and cable than other methods of arraying loudspeakers. The lower portion of the line array is generally curved backward to increase dispersion at the bottom of the array and allow sound to reach more audience members. Typically, cabinets used in line arrays are trapezoidal, connected together by specialized rigging hardware.[4]

* 1 History
* 2 Theory
* 3 High frequencies
* 4 Configurations
* 5 Design and Rigging
* 6 References

[edit] History
Four-driver column loudspeaker polar patterns, taken at six frequencies

The line array effect of the narrowing of the beam with increasing frequency was first demonstrated by acoustical pioneer Harry Olson.[5] He published his findings in his 1957 text, Acoustical Engineering.[6] Olson used line array concepts to develop the column speaker in which vertically aligned drivers in a single enclosure produced mid-range output in a wide horizontal and narrow vertical pattern. Line arrays have been around for over half a century but until recently most were voice range only. The application for these were for highly reverberant spaces where a narrow vertical design kept from exciting the reverberant field.[7]

A multi-band line array elements in a horizontally oriented enclosure was suggested by Joseph D'Appolito in 1983.[8] However it was L-Acoustics' V-DOSC line array in the mid-1990s that would show the concert world that a more level and smoother frequency response can come from fewer boxers in a line array. As soon as people realized that there was no destructive interference in the horizontal plane and waves combine mostly in phase in the vertical plane, the race was on for loudspeaker manufacturers.[9]
[edit] Theory

Line arrays create a cylindrical wave front in the near field, providing a 3 dB drop off per doubling of distance due to frequencies combining in phase. This is more prominent at high frequencies because they create more interference than low frequencies, due to the shorter wavelengths. But eventually the cylindrical field will transform into a spherical one, this is known as the far field. When the far-field boundary is crossed, the interference has diminished enough for the SPL to decay at the normal 6dB for doubling of distance.[10] This is opposed to the point source which radiates in a spherical waveform which equates to a 6 dBSPL drop.

Interference pattern is the term applied to the dispersion pattern of a line array. It means that when you stack a number of loudspeakers vertically, the vertical dispersion angle decreases because the individual drivers are out of phase with each other at listening positions off-axis in the vertical plane. The taller the stack is, the narrower the vertical dispersion will be and the higher the sensitivity will be on-axis. A vertical array of like drivers will have the same horizontal polar pattern as a single driver.

Other than the narrowing vertical coverage, the length of the array also plays a role in what wavelengths will be affected by this narrowing of dispersion. The longer the array, the lower frequency the pattern will control.[11] At frequencies below 100 Hz (wavelength of 11.3 ft) the drivers in a line array will start to become omni-directional, so the system will not conform to line array theory across all frequencies.[12] It is theoretically possible to construct an audio line array that follows the theory at low frequencies. However, the array requires more than 1,000 fifteen-inch drivers, spaced twenty inches center to center, to do it.[13] Above about 400 Hz the low-frequency cones become directional, again violating the theory’s assumptions, and at high frequencies, many practical systems use directional waveguides whose behavior cannot be described using classical line array theory. In short, the geometry of real-world audio line arrays is too complicated to be modeled accurately by ‘pure’ line array theory.[14]
[edit] High frequencies

Practical line array systems act as line sources only in the low- and mid- frequencies. For the high frequencies, some other method must be employed to attain directional characteristics that match those of the lows and mids. The most practical method for reinforcement systems is to use wave guides (horns) coupled to compression drivers. Each horn must have a very narrow vertical and a very wide horizontal dispersion.

Rather than using constructive and destructive interference, horns achieve directionality by reflecting sound into a specified coverage pattern. In a properly designed line array system, that pattern should closely match the low-frequency directional characteristic of the array. If the array's vertical dispersion is 60 degrees and there are 12 boxes, then each horn would need to have 5 degree vertical coverage. (Narrow vertical coverage has the benefit that it minimizes multiple arrivals, which would harm intelligibility.) If this is achieved, then the wave guide elements can be integrated into the line array and, with proper equalization and crossovers, the beam from the high frequencies and the constructive interference of the low frequencies can be made to align so that the resulting arrayed system provides consistent coverage.
[edit] Configurations

Two configurations that are rarely used are the straight and curved array.The problem with curved arrays is that they are not very well suited to the average venue. While the bottom half will be angled down to provide extra coverage at locations close to the front of stage, the top half will be angled upwards at the ceiling. Also, the problem with straight line arrays is that the beam is far too narrow at high frequencies. A solution to utilise the best features of both arrays is to use a ‘J’ array. This is made up of a straight line portion and a curved portion, normally at the bottom. This provides a long throw straight line component for people relatively far away, while the curve at the bottom acts as an in-fill for the area underneath the array that would otherwise be neglected

Spiral arrays are the next development from J-arrays, and have a superior frequency response due to their similar polar pattern at shifting frequencies, while still retain the long throw and in-fill benefits that J-arrays provide. The concept is that spiral arrays are curved all the way along the array, but the curve is progressive. This means that the top of the array is almost straight with angles of 1° between boxes, and increase at the bottom to 6° up to about 10°. A well designed spiral array could have an almost constant directivity pattern with frequency, with some small lobes exhibited at low frequencies.[15]
[edit] Design and Rigging
Two different line arrays rigged near a cluster of subwoofers

Large-format line arrays are designed for large venues or outdoor festivals. These boxes typically included multiple vertically aligned high frequency compression drivers and multiple midrange and low drivers arranged symmetrically around the compression driver. The low frequency driver is typically 15 or 18 inches in diameter. Mid-format line arrays are typically two or three way and use 10 or 12 inch low-frequency drivers. The horizontal coverage is typically 90 degrees wide but some systems employ narrower boxes at the top or wider boxes at the bottom of the array. Using a transition frame (which aligns the rigging on dissimilar systems), system engineers may sometimes hang a mid-format box below a large-format box to cover the closest audience members. Speaker boxes from different manufacturers are not mixed because each system has a particular 'voicing' which may be common to a single manufacturer.

Manufacturers typically provide a spreadsheet or custom program to design arrays. Examples include L-Acoustics SOUNDVISION[16], Adamson Shooter,[17] Electro-Voice LAPS (Line Array Prediction Software),[18] and JBL Vertec Line Array Calculator.[19] Renkus Heinz offers a program called EaseFocus. It is similar to EASE but has only features and calculations specific to Line arrays. EaseFocus has data for a large number of manufacturers allowing comparison of several loudspeaker systems. Meyer Sound offers a different solution by providing an online system called MAPP Online Pro[20]

The design process starts by entering the dimensions of the room and the required sound pressure level. The program then suggests the number and arrangement of boxes. Alternatively some programs require you to enter the number of boxes and it will predict the resulting sound pressure levels in different parts of the room.

Once designed, the rigging points are hung from the structure, followed by chain motors (or blocks), flying frame and then the speakers. The individual boxes may be connected one at a time or rigged together on the ground and then pulled up. As the array is lifted, individual box angles are adjusted to match the array prediction program. The top frame may have an inclinometer to confirm the angle of the frame or laser attached which indicates the upper aiming point of the array.

If height or lack of rigging points doesn't permit flying the speakers, the speakers are typically stacked on the stage or on subwoofers[21] using a custom stacking frame. Stacking of line arrays is common in smaller venues and in temporary installations. Compared to flown speakers, they require less vertical dispersion to cover front to back and the resulting array will have little curvature.
[edit] References

1. ^ L-Acoustics Line Source Products Page; L-Acoustics Technical bulletin
2. ^ Ground support tower
3. ^ [
4. ^ SoundOnSound Live magazine, Issue 7, March 2006
5. ^ JBL's development team talks about line array concepts
6. ^
7. ^
8. ^ JBL's development team talks about line array concepts
9. ^
10. ^
11. ^
12. ^
13. ^
14. ^
15. ^
16. ^
17. ^ Adamson Shooter software
18. ^ Electro-Voice LAPS
19. ^ JBL Vertec Line Array Calculator
20. ^ Meyer Sound MAPP Online Pro
21. ^ EAW KF730 stack on SB730
sưu tầm và biên tập từ nhiều nguồn, mọi ý kiến về kỹ thuật xin vui long liên hệ – 0906 715 077 rất mong được đóng góp của các độc giả.

Không có nhận xét nào:

Đăng nhận xét